Arofanatics Fish Talk Forums

Arofanatics Fish Talk Forums (http://www.arofanatics.com/forums/index.php)
-   Freshwater Invertebrates Forum (http://www.arofanatics.com/forums/forumdisplay.php?f=68)
-   -   my noobie starter tank. (http://www.arofanatics.com/forums/showthread.php?t=470673)

midniteguy 21-07-2011 11:44 PM

my noobie starter tank.
 
almost done with cycling le (:
still got 2 tubs of US fissiden to tie onto mesh and need replace the inlet of the canister and lastly i need to custom make a divider, anything i am missing out?

http://forums.vr-zone.com/photopost/...10721-2107.jpg
http://forums.vr-zone.com/photopost/...10721-2108.jpg
http://forums.vr-zone.com/photopost/...10721-2107.jpg
http://forums.vr-zone.com/photopost/...10721-2108.jpg

the dw are not in their final place yet, just tossing everything in den arrange when i am done with all the moss.

eviltrain 22-07-2011 12:23 AM

Hee hee, another shrimp tank start up lo. Looking good. Huat ah!

midniteguy 22-07-2011 12:35 AM

this time running 2x 2 tube T5 light, hailea 300A, atman cf 1200, 2 pkt of ADA amazonia 2, Co2 set ready but haven set up.

now is need to find somewhere to custom make a divider and for external temp probe for my chiller ):

gryphon 22-07-2011 09:44 AM

Looking good with a nice big setup

Ariesdram 22-07-2011 11:17 AM

Looks good. Thanks for sharing :)

midniteguy 22-07-2011 12:39 PM

anyone know where to get custom sized divider? intending to use the bro evil train method of using air tubing to stick the divider in place. or any other ideas for the divider?

and also where sell the steel inlet cover cheap ar? spending 16$ one kinda steep :S

bai 22-07-2011 12:58 PM

Quote:

Originally Posted by midniteguy (Post 8562014)
anyone know where to get custom sized divider? intending to use the bro evil train method of using air tubing to stick the divider in place. or any other ideas for the divider?

and also where sell the steel inlet cover cheap ar? spending 16$ one kinda steep :S

if u mean the stainless steel cover for ur canister inlet. U can get from GC is less then a red notes.

eviltrain 22-07-2011 01:04 PM

the divider can custom make at serangoon north hardware shop ( the stretch along the ex location of rainbow )

midniteguy 22-07-2011 01:10 PM

Quote:

Originally Posted by bai (Post 8562057)
if u mean the stainless steel cover for ur canister inlet. U can get from GC is less then a red notes.

oohh okies, that seem reasonable.

[qoute]the divider can custom make at serangoon north hardware shop ( the stretch along the ex location of rainbow ) [/qoute]

so i measure the inside of the tank and give it a few mm spacing?
hmmm should i get 2 den i can put some netting or wire mesh inbetween?

eviltrain 22-07-2011 01:13 PM

yapz, measure the inside of the tank ( B X H ) and gives 1-2 mm more spacing on each side.


All times are GMT +9. The time now is 11:03 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright © 2000-2008 Arofanatics.com (Since 30th August 2000)