Arofanatics Fish Talk Forums  

Go Back   Arofanatics Fish Talk Forums > General Aquatic Forums > AroReefers > Equipment/DIY discussion

Reply
 
Thread Tools Display Modes
Old 09-11-2008, 11:11 PM   #61
sherman
Guest
 
Posts: n/a
Default

If I have more 4 w led will be better.
  Reply With Quote
Old 26-11-2008, 02:47 PM   #62
BarraCuda™
SiaoGu Gives You Wings
 
BarraCuda™'s Avatar
 
Join Date: Jul 2001
Posts: 4,169
Default

Bad news .. I think I got a bad batch of luxeon V. All my luxeon V have clouded lens .



Well .. time to change the luxeons out for CREE XR-E.
BarraCuda™ is offline   Reply With Quote
Old 18-12-2008, 12:36 PM   #63
sherman
Guest
 
Posts: n/a
Default

Attached an excel spreadsheet of the light measurement
Attached Files
File Type: doc 2 ft T5HO light reading.doc (40.5 KB, 936 views)
  Reply With Quote
Old 05-01-2009, 10:56 PM   #64
Kazuo
Guest
 
Posts: n/a
Default

Where you guys get the luxeon LED from?
  Reply With Quote
Old 06-01-2009, 02:39 AM   #65
PatrikLim
Dragon
 
PatrikLim's Avatar
 
Join Date: Aug 2006
Posts: 1,125
Default

Quote:
Originally Posted by Kazuo View Post
Where you guys get the luxeon LED from?
i think bro barra mentioned supplied from www.ledsupply.com
PatrikLim is offline   Reply With Quote
Old 06-01-2009, 11:47 AM   #66
Kazuo
Guest
 
Posts: n/a
Default

Oh... no locally huh?
  Reply With Quote
Old 17-01-2009, 12:37 PM   #67
Limsteel
Arofanatic
 
Limsteel's Avatar
 
Join Date: Feb 2003
Posts: 289
Default

IS LED DRIVER A MUST FOR HIGH POWER LED? I planning to connect them as if they are normal low current LED setup. 12VDC (Laptop charger with a few Amps) + resistor + LED = Light

I bought 10 x 3W White LED... got the shipment and I tested using a 9V batt with 100Ω... With this I should get around 40mA running through the LED. 2 out of 10 are dead. When I talked to the supplier, they replied they will not replace the LED as I use Batt+resistor to power them. They claimed that this will burn the LED. trying to BS me!

These 3W LED runs on 3.5V and 700mA. How can a mere 40mA killed it! what logic?

Last edited by Limsteel; 17-01-2009 at 12:47 PM.
Limsteel is offline   Reply With Quote
Old 18-01-2009, 02:12 PM   #68
BarraCuda™
SiaoGu Gives You Wings
 
BarraCuda™'s Avatar
 
Join Date: Jul 2001
Posts: 4,169
Default

Quote:
Originally Posted by Limsteel View Post
IS LED DRIVER A MUST FOR HIGH POWER LED? I planning to connect them as if they are normal low current LED setup. 12VDC (Laptop charger with a few Amps) + resistor + LED = Light

I bought 10 x 3W White LED... got the shipment and I tested using a 9V batt with 100Ω... With this I should get around 40mA running through the LED. 2 out of 10 are dead. When I talked to the supplier, they replied they will not replace the LED as I use Batt+resistor to power them. They claimed that this will burn the LED. trying to BS me!

These 3W LED runs on 3.5V and 700mA. How can a mere 40mA killed it! what logic?
Where you got them from?
BarraCuda™ is offline   Reply With Quote
Old 18-01-2009, 06:06 PM   #69
Limsteel
Arofanatic
 
Limsteel's Avatar
 
Join Date: Feb 2003
Posts: 289
Default

got them from Ebay.
Limsteel is offline   Reply With Quote
Old 18-01-2009, 10:22 PM   #70
BarraCuda™
SiaoGu Gives You Wings
 
BarraCuda™'s Avatar
 
Join Date: Jul 2001
Posts: 4,169
Default

I wouldnt advise using resistors to drive your LEDs. Its difficult to regulate the voltage and current at the same time. Resistors are also not power efficient thus using more power than required.

If you want 40mA, you should be using 150ohm, 1/2watt resistor with a 9V supply. That would be good for testing but not good for driving these high powered LEDs.

To drive at 700mA, you will need 15ohm, 7.4watt with 12V supply. To drive all 10 LEDs using resistors. You will be wasting at least 10watts of power heating the resistors.
BarraCuda™ is offline   Reply With Quote
Reply

Tags
coral, diy, led, light


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +9. The time now is 08:46 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright © 2000-2008 Arofanatics.com (Since 30th August 2000)