Arofanatics Fish Talk Forums  

Go Back   Arofanatics Fish Talk Forums > Arowana Forum > Tank set-ups, Filtration & Water Management

Reply
 
Thread Tools Display Modes
Old 25-05-2013, 12:17 AM   #31
Occellatus
Endangered Dragon
 
Occellatus's Avatar
 
Join Date: Jul 2005
Posts: 10,797
Default

My endy from below also luan kan. So late liao still open glass cover to disturb them.
Occellatus is offline   Reply With Quote
Old 25-05-2013, 12:18 AM   #32
Flairtender
Dragon
 
Flairtender's Avatar
 
Join Date: Jul 2001
Posts: 1,141
Default

Tio lah lah , cannot measure from the side cause if got oyama cannot see !

U dun actually have to open the top cover also .... glass cover is transparent and can measure overlapping if u know wat i mean .
Flairtender is offline   Reply With Quote
Old 25-05-2013, 12:20 AM   #33
Occellatus
Endangered Dragon
 
Occellatus's Avatar
 
Join Date: Jul 2005
Posts: 10,797
Default

Quote:
Originally Posted by Flairtender View Post
Tio lah lah , cannot measure from the side cause if got oyama cannot see !

U dun actually have to open the top cover also .... glass cover is transparent and can measure overlapping if u know wat i mean .
Ok. I will bring your dimensions to go cut tomorrow. Should be correct based on what I've counter measured earlier. I will tell them to split the entire thing into half so that I can place them in.
Occellatus is offline   Reply With Quote
Old 25-05-2013, 12:28 AM   #34
Flairtender
Dragon
 
Flairtender's Avatar
 
Join Date: Jul 2001
Posts: 1,141
Default

Quote:
Originally Posted by Occellatus View Post
Ok. I will bring your dimensions to go cut tomorrow. Should be correct based on what I've counter measured earlier. I will tell them to split the entire thing into half so that I can place them in.
Put in must got skill also hoh .

First lower the pc without EOS halfway only and use a long pvc pipe or those mr aqua ohf long piping . ( Inverted broom also can lah )

Hold half the acrylic and slowly lay down once u get it to sit in between ur bracing , then slowly use the hard piping to push to the end first .

The again do the same for the eos part , leave some gap for the EOS part so next time can remove easily .

(* My dimension already got gap allowance so dun go and minus further )
Flairtender is offline   Reply With Quote
Old 25-05-2013, 12:31 AM   #35
Occellatus
Endangered Dragon
 
Occellatus's Avatar
 
Join Date: Jul 2005
Posts: 10,797
Default

Don't understand. Wahahahhahaha.......

Laying should be ok la. Should not be that hard. If keep fish so long lay acrylic also cannot then die Liao.

Tomorrow the toa payoh shop open? Any idea?
Occellatus is offline   Reply With Quote
Old 25-05-2013, 12:36 AM   #36
Flairtender
Dragon
 
Flairtender's Avatar
 
Join Date: Jul 2001
Posts: 1,141
Default

Quote:
Originally Posted by Occellatus View Post
Don't understand. Wahahahhahaha.......

Laying should be ok la. Should not be that hard. If keep fish so long lay acrylic also cannot then die Liao.

Tomorrow the toa payoh shop open? Any idea?

When u lay not too fast also , ur fish will get stress from the new white acrylic . Try buy the matt white type .

Toa payoh ?? Dama at UBI leh .... sat go long queue ah !!! I go weekdays , half and hour , slant cut also gao tim liao . If all straight cut lagi fast .
Flairtender is offline   Reply With Quote
Old 25-05-2013, 12:38 AM   #37
Occellatus
Endangered Dragon
 
Occellatus's Avatar
 
Join Date: Jul 2005
Posts: 10,797
Default

Quote:
Originally Posted by Flairtender View Post
When u lay not too fast also , ur fish will get stress from the new white acrylic . Try buy the matt white type .

Toa payoh ?? Dama at UBI leh .... sat go long queue ah !!! I go weekdays , half and hour , slant cut also gao tim liao . If all straight cut lagi fast .
Ok I get the Matt type. Long queue? So many ppl doing acrylic on sats ar?

The tpy is cut tiles one. Solly, got mixed up.
Occellatus is offline   Reply With Quote
Old 25-05-2013, 12:41 AM   #38
Flairtender
Dragon
 
Flairtender's Avatar
 
Join Date: Jul 2001
Posts: 1,141
Default

Quote:
Originally Posted by itchy View Post
Bro, can trouble you to help fellow Buangkokrian to measure when you free? Thinking to chnage white base see see
Bro u are lucky , i got something easy to measure and comfirm ur measurement . Pm me ur no .
Flairtender is offline   Reply With Quote
Old 25-05-2013, 12:44 AM   #39
Flairtender
Dragon
 
Flairtender's Avatar
 
Join Date: Jul 2001
Posts: 1,141
Default

Quote:
Originally Posted by Occellatus View Post
Ok I get the Matt type. Long queue? So many ppl doing acrylic on sats ar?

The tpy is cut tiles one. Solly, got mixed up.

Supplier from all chain .... I also see ppl custom made those 4 to 5 footer big denitrator or protein skimmer there also . All those reefers favourite DIY place .
Flairtender is offline   Reply With Quote
Old 25-05-2013, 12:49 AM   #40
Occellatus
Endangered Dragon
 
Occellatus's Avatar
 
Join Date: Jul 2005
Posts: 10,797
Default

Quote:
Originally Posted by Flairtender View Post
Supplier from all chain .... I also see ppl custom made those 4 to 5 footer big denitrator or protein skimmer there also . All those reefers favourite DIY place .
Good lord. I better go early then. Be the first in line. Go early finish early.
Occellatus is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +9. The time now is 04:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright © 2000-2008 Arofanatics.com (Since 30th August 2000)